Get Real D-PCM-DY-23 Quesions Pass EMC Certification Exams Easily
D-PCM-DY-23 Dumps are Available for Instant Access
NEW QUESTION # 82
Which command will show the policy-based routing map applied on an interface?
- A. show ip interface
- B. show ip access-lists
- C. show ip policy
- D. show route-map
Answer: C
NEW QUESTION # 83
Which decimal value is used to indicate Assured Forwarding when implementing DSCP prioritization?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 84
Which ports on a spanning tree root switch are always forwarding?
- A. Backup ports
- B. Root ports
- C. Designated ports
- D. Alternate ports
Answer: C
NEW QUESTION # 85
Which technology is designed to protect against a default gateway failure and downtime in the Dell PowerSwitch N-Series switches?
- A. CARP
- B. MLAG
- C. VRRP
- D. HSRP
Answer: C
NEW QUESTION # 86
Refer to the Exhibit.
Switch-1(config)# radius server host 10.1.1.111
Switch-1(config-radius)# key "secretkey"
Switch-1(config-radius)# exit
Switch-1(config)# aaa authentication login "LOCAL-AUTH" local
Switch-1(config)# aaa authentication login "REMOTE-AUTH" radius local
Switch-1(config)# aaa authentication enable "REMOTE-AUTH" radius enable Switch-1(config)# aaa authentication login default tacacs local Switch-1(config)# aaa authentication enable default tacacs enable Switch-1(config)# line telnet Switch-1(config-telnet)# login authentication "REMOTE-AUTH" Switch-1(config-telnet)# exit Switch-1(config)# line ssh Switch-1(config-ssh)# login authentication default Switch-1(config)# exit Switch-1(config)# line console Switch-1(config-line)# login authentication "LOCAL-AUTH" Switch-1(config-line)# exit Which authentication method will be used if a user tries to login to the switch when accessing through SSH?
- A. None
- B. RADIUS, then fails over to a local user account
- C. Local user account
- D. TACACS, then fails over to a local user account
Answer: D
NEW QUESTION # 87
When DSCP is used for QoS prioritization, which type of service is typically used for voice traffic?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 88
Which interface on a Dell EMC N-Series switch provides the most security for management?
- A. Loopback
- B. Out-of-band
- C. VLAN
- D. Ethernet
Answer: B
NEW QUESTION # 89
What is the recommended maximum number of routers, per area, when using OSPF?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 90
What is an accurate statement about configuring a LAG on a Dell EMC N-Series switch?
- A. At least one interface must be a trunk port
- B. A physical interface can belong to only one port-channel
- C. All interfaces in the port-channel can be configured for different speeds
- D. A port-channel is considered up when all members in the link are up
Answer: B
NEW QUESTION # 91
What happens when a match is found for an ACL with 15 entries?
- A. All packets which match that entry are dropped
- B. Action from that entry is performed and the ACL is exited
- C. Action from that entry is performed and the rest of the entries in the ACL are processed
- D. All packets which match that entry are forwarded
Answer: B
NEW QUESTION # 92
Which Dell EMC N-Series switch models can have up to 12 of the same switch model in a stack?
- A. N1500 and N2000
- B. N1500 and N4000
- C. N2000 and N4000
- D. N1100 and N1500
Answer: C
NEW QUESTION # 93
Which two are true about discovery protocols on the Dell N-Series Voice VLAN feature? (Select 2)
- A. Only used ISDP
- B. Only uses LLDP
- C. A Cisco phone can be configured by CDP
- D. Uses both LLDP and ISDP
- E. A Cisco phone can only be discovered by CDP
Answer: C,D
NEW QUESTION # 94
What are key features of the Dell EMC N4064 or N4064F switches?
- A. Up to 1.2 Tbps switch fabric capacity and up to 64-line rate 10GbE ports per switch
- B. Up to 48-line rate 10GbE ports per switch and hot swap expansion module support for dual QSFP+ (8 x 10GbE)
- C. Up to 640 Gbps switch fabric capacity and hot swap expansion module support for dual QSFP+ (8 x
10GbE) - D. Up to 1.0 Tbps switch fabric capacity and up to 48-line rate 10GbE ports per switch
Answer: C
NEW QUESTION # 95
In a PoE environment, for which device is POE+ most likely to be required?
- A. Wireless Access Points
- B. Environmental Sensors
- C. Voice+Video IP Phones
- D. Access Controls
Answer: C
NEW QUESTION # 96
Which Dell OS6 command displays the IPv6 address of the default gateway and the default route associated with the gateway?
- A. show ip route
- B. show ipv6 brief
- C. show ip mroute
- D. show ipv6 route
Answer: D
NEW QUESTION # 97
Based on the topology shown in the graphic, which ports are designated ports?
- A. Switch B port Te1/0/3 and Switch C port Te1/0/6
- B. Switch B, ports Te1/0/3 and Te1/0/4
- C. Switch C, ports Te1/0/5 and Te1/0/6
- D. Switch A, ports Te1/0/1 and Te1/0/2
Answer: D
NEW QUESTION # 98
After setting up the VoIP configuration, a network administrator issues the following commands with the results shown:
- console# show voice vlan Administrative
- Mode...........................Enable
- console# show voice vlan it gi 1/0/2
- Interface........................................Gi1/0/2
- Voice VLAN Interface Mode...............Enabled
- Voice VLAN ID...............................10
- Voice VLAN COS Overwrite...............False
- Voice VLAN DSCP Value...................46
- Voice VLAN Port Status.....................Enabled
- Voice VLAN Authentication................Disabled
Based on this information, what is the Layer 3 QoS value?
- A. 0
- B. Gi1/0/2
- C. 1
- D. 2
Answer: C
NEW QUESTION # 99
A group of four switches are configured to be part of a VRRP group with the following configurations:
- Switch1: IP 192.168.10.11, Priority 11
- Switch2: IP 192.168.10.12, Priority 12
- Switch3: IP 192.168.10.13, Priority 13
- Switch4: IP 192.168.10.14, Priority 14
The switches are initially disconnected from the network and come online in the following order: Switch3, Switch2, Switch4, Switch1.
If preempt is disabled, which switch is expected to be the Primary?
- A. Switch4
- B. Switch3
- C. Switch2
- D. Switch1
Answer: B
NEW QUESTION # 100
A Dell EMC N-Series switch is configured to uplink to a customer switch using two separate 4-port port-channels configured as trunks. Both switches are configured with 16 VLANs and RSTP.
How will VLAN traffic be distributed across the port-channels?
- A. All VLANs are allowed across a single port-channel
- B. Eight VLANs are allowed across each port-channel
- C. All VLANs are allowed across both port-channels
- D. A single VLAN is allowed across each port-channel
Answer: A
NEW QUESTION # 101
What Dell PowerSwitch N-Series switches require QSFP28 to be used for stacking?
- A. N1500
- B. N1100
- C. N3200
- D. N2200
Answer: C
NEW QUESTION # 102
Refer to the exhibit:
Which authentication method will be used if a user tries to log into the switch when accessing through the console port?
- A. None
- B. TACACS
- C. Local user account
- D. RADIUS
Answer: C
NEW QUESTION # 103
A Master switch failed in a Dell EMC N-Series three-unit switch stack and the Standby switch assumed the role of Master.
What happens when the failed Master switch rejoins the stack after the new Master has taken over?
- A. Switch joins the stack and resumes as the Master
- B. Switch must be manually configured to rejoin the stack
- C. Switch joins the stack as the Standby
- D. Switch joins the stack as a Member
Answer: D
NEW QUESTION # 104
What is the PoE source maximum power budget for a Class 3 end device?
- A. 12.95 watts
- B. 60 watts
- C. 15.4 watts
- D. 30 watts
Answer: C
NEW QUESTION # 105
How many bits are in each section of an IPv6 address?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 106
......
Get Instant Access REAL D-PCM-DY-23 DUMP Pass Your Exam Easily: https://examcertify.passleader.top/EMC/D-PCM-DY-23-exam-braindumps.html