Easily To Pass New HP HPE2-T37 Dumps with 41 Questions
Latest HPE2-T37 Study Guides 2022 - With Test Engine PDF
NEW QUESTION 20
For HPE Primera, match each task with the management tool that can be used to perform it.
Answer:
Explanation:
NEW QUESTION 21
Your customer built a sever profile for HPE Synergy Gen 10 server and configured boot mode to Legacy BIOS. Which feature Is not available for this Compute Module?
- A. Workload profile
- B. Boot from SAN
- C. BIOS management
- D. Secure boot
Answer: D
NEW QUESTION 22
You try to add an HPE Primera array to HPE OneView, but you get a connectivity error. However, you can connect to the array using SSMC. What should you verify before adding HPE Primera to HPE OneView?
- A. whether array management using HPE OneView is enabled in SSMC.
- B. whether there are at least two Fibre Channel networks defined in HPE OneView.
- C. whether WSAPI service is enabled on HPE Primera array.
- D. whether the appropriate license for HPE Primera Is available in HPE OneView.
Answer: C
NEW QUESTION 23
What is the best practice when deploying an HPE OneView appliance?
- A. Deploy two HPE OneView appliances and configure them in HA mode.
- B. Use thin-provisioning for the HPE OneView appliance to save storage capacity.
- C. Enable VMware Fault Tolerance if the appliance is deployed to a VMware hypervisor.
- D. deploy the appliance in a hypervisor cluster that Is not managed by OneView.
Answer: D
NEW QUESTION 24
Refer to the exhibit.
Your customer created multiple networks in HPE OneView, but only Eth-1 is available to be used within a server profile. What is a likely cause of this situation?
- A. The other networks are not added to the Logical Interconnect Group configuration.
- B. The other networks are not configured with the required Smart Link parameter.
- C. The other networks have Private Network' selected, which hides them from Compute Modules.
- D. The other networks are configured with a purpose other than General or Management.
Answer: C
NEW QUESTION 25
Your customer asks you if it is possible to perform HPE Synergy initial setup remotely. How should you respond?
- A. HPE Synergy can be configured remotely through a secure connection to the FLM if this option was enabled In the factory.
- B. Remote HPE Synergy setup is possible if HPE Composer 2 is used and a DHCP server Is available in the management network.
- C. Remote HPE Synergy Installation can be done only if an additional set of the services was purchased together with hardware platform.
- D. HPE Synergy cannot be deployed remotely, as Initial setup must be performed using a local console connection.
Answer: A
NEW QUESTION 26
You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?
- A. An upgrade license must be purchased and deployed.
- B. Both FlexNlCs must be connected to the same network.
- C. The Compute Module profile must have exactly two connections defined.
- D. The sFlow option must be enabled and configured.
Answer: D
NEW QUESTION 27
What is required to add remote frame link topology to HPE OneView?
- A. Management ports of the remote frame link topology must be connected to the management LAN.
- B. The HPE OneView certificate from the primary site must be added to HPE OneView in the remote site.
- C. Multi-site licenses must be added to HPE OneView and activate for all available HPE Synergy frames.
- D. The IP address assigned to HPE Composer installed in a remote site must be registered in a primary site.
Answer: C
NEW QUESTION 28
Which statement about a server profile for an Apollo system is true?
- A. Enclosure Group Is automatically selected
- B. Virtual WWNs and MAC addresses can be defined
- C. UEFI optimized is the only available boot mode
- D. Fibre Channel connections can be defined
Answer: B
NEW QUESTION 29
Your customer wants to use HPE OneView for VMware vCenter Server to simplify management of their VMware cluster running on HPE Synergy. The customer is concerned with the cost of additional licenses.
How will you explain licensing rules for this product?
- A. If the number of the HPE Synergy Compute Modules installed in HPE Synergy frame is less than 10, no license is required to use HPE OneView tor VMware vCenter Server.
- B. As long as the customer has HPE OneVtew Global Dashboard deployed, HPE OneView for VMware vCenter Server does not require any additional licenses.
- C. One HPE OneView for VMware vCenter Server license is required per HPE Synergy frame if more than
10 Compute Modules are installed in the frame. - D. As long as the server is managed using HPE OneView. the customer can use HPE OneView for VMware vCenter Server without additional licenses.
Answer: C
NEW QUESTION 30
Refer to the exhibit.
After adding SAN Manager to HPE OneView. you noticed that all SANs are in the discovered state. How will this affect HPE OneView storage management capabilities?
- A. Volume provisioning will only work for arrays that ate accessible through these SANs.
- B. Snapshot functionality will be limited only to the volumes not using these SANs.
- C. Auto-zoning functionality will not work until SANs are associated with networks.
- D. Volume presentation through server profile will work with the discovered state.
Answer: D
NEW QUESTION 31
Refer to the exhibit.
Which statement about the logical interconnect shown is true?
- A. For FC uplink sets, an additional uplink from second module should be added for redundancy.
- B. The maximum supported number of the internal networks for logical interconnect is configured.
- C. Additional uplink ports can be added to ETH-Uplink to increase available bandwidth.
- D. FC uplinks are not supported and will be converted to FCoE or RoCE uplinks.
Answer: D
NEW QUESTION 32
Your customer added HPE Primera to HPE OneVlew and enabled volume provisioning on all storage pools.
For security reasons, the customer wants to disable volume provisioning using HPE OneView on a specific storage pool.
How can this task be completed?
- A. The storage pool should be disabled using the array management tool.
- B. The storage pool should be removed from HPE OneView using a PowerShell script.
- C. The storage pool state should be changed to discovered using HPE OneView.
- D. The storage pool should be marked as read-only using HPE OneView.
Answer: A
NEW QUESTION 33
Which components require an HPE OneView license for management?
- A. HPE Virtual Connect modules
- B. HPE Primera and HPE 3PAR
- C. Brocade and Cisco SAN Manager
- D. HPE Apollo XL 170r
Answer: A
NEW QUESTION 34
Which HPE components can be managed using HPE Composer? (select two.)
- A. HPE B-series SN6600B Fibre Channel Switch
- B. HPE Synergy Virtual Connect SE 32Gb FC Module
- C. HPE MSA 2062 Storage Array
- D. HPE Synergy 480 Compute Modules
- E. HPE Superdome Flex 280
Answer: A,B
NEW QUESTION 35
After replacing a failed Compute Module, you notice the server profile Is not automatically assigned to the replaced server hardware. What can cause this issue?
- A. IL0 firmware of the replacement server is different than firmware in broken server.
- B. Server profile affinity is configured to Device Day + server hardware.
- C. The replacement server has more memory or CPUs than broken machine.
- D. The enclosure group has to be updated to match the original enclosure group.
Answer: A
NEW QUESTION 36
......
HPE2-T37 Dumps and Exam Test Engine: https://examcertify.passleader.top/HP/HPE2-T37-exam-braindumps.html